IMAGENICS / CRO-UF2T

An optical extender transmitter that transmits HDMI 2.0 4K@60Hz (4:4:4) uncompressed video up to 2km using two single-mode optical fiber cables or one cable.

■4K HDMI (DVI) Optical Extender (Single Mode) Transmitter
■4K Signaling System
TMDS Clock: 25MHz to 340MHz
Pixel Clock: 25MHz to 600MHz
Data Rate: 0.75 to 18Gbps
HDCP: 1.4/2.2
Supported Resolutions: 4K60p 4:4 (24-bit), 4K60p 4:2 (236-bit), 4K30p 4:4 (36-bit), etc.
■Video Input/Output
One HDMI Type A 19-pin connector input
One HDMI Type D One 19-pin connector output (for information screen output only)
Automatically supports 4K, D1-D5 equivalent HDMI signals and PC signals from 640x480 to 4,096x2,160
Input cable length: 3m (when using an Imagenics HDMI cable)
■Optical Input/Output
Optical Output Level: 8.5dBm maximum (average power)
Optical Input Level: -8dBm to 2.5dBm (average power)
Laser Wavelength: 1264.5nm to 1337.5nm
Connector: LC (Duplex)
Optical Fiber: Single-mode optical fiber cord (9.5/125μm) Category OS1 equivalent
*Bend-resistant single-mode optical fiber cord 8μm core diameter can also be used.
Laser Safety: Class 1 (JISC6902IEC60825-1)
Transmission Distance (Reference Value): Maximum approx. 2km
■Audio Input/Output
Input Terminal: -10dBu, approx. 30kΩ, φ3.5mm stereo mini jack, unbalanced, 2 channels x 1
Audio Frequency Response: -1dB to +1dB from 20Hz to 20kHz
Audio S/N Ratio: Over 80dB (passed a 1kHz A-weighting filter, reference -10dBu output)
Audio Distortion: Less than 0.1%
Audio Sampling: 24-bit, 48kHz linear PCM
Maximum Input/Output Level: +10dBu (HDMI embedded audio output at 0dBFS)
■RS-232C:
D-SUB9 (male) connector, full-duplex (bidirectional) communication, 1 channel
Flow control: Hardware, None / Data bit length: 8 bits / Stop bit length: 1 bit / Baud rate: 9.6 kbps, 19.2 kbps, 38.4 kbps / Parity: None, Even
■ Built-in features:
Plug-and-play function (built-in EDID emulation, external EDID pass-through or copy/retain function), analog audio embedding function, operating status information screen display function (press and hold the PUSH button on the front to switch from input video to information screen) *In addition to switching the information screen, the information screen can also be displayed via the INFO terminal (HDMI) on the front Continuous output is possible from the HDMI Type D connector.
■Power Supply/Power Consumption: DC5V 1.2A 6W (Max.)
■Size: 100(W) x 25(H) x 150(D) mm
※※When transmitting using a single cable, RS-232C transmission is only possible for sending; EDID through/copy functions are disabled.
※Depth including the optical module pull tab is 234mm.
※Do not remove the optical module by pulling the blue pull tab (operation is not guaranteed).
■Weight: Approximately 500g
■Accessories: AC100V 27VA 50Hz/60Hz (Japan-only) AC Adapter (5V 2.3A output with lock), HDMI Locking Bracket (CL-1) + Cable Tie (Set of Each). The HDMI Locking Bracket (CL-1) may not function properly depending on the thickness of the HDMI connector to be attached.

""