A controller that provides comfortable control such as Focusrite RED 8 PRE.
■ Controller
■ For FOCUSRITE RED series
Desktop remote controller that extends the Focusrite Red series B>
RedNet R1 is more than just a remote controller.
It is an expansion device developed to unleash the power of the RED series represented by Focusrite RED 8 PRE.
You can instantly switch between Protools HDX, other DAWs, RED series outputs, and I / O output formats and destinations within your Dante audio network, as well as control RED series inputs and output levels. increase.
Seamless switching of input sources B>
You can save up to eight output formats from monaural to 7.1.4ch, and switch from monaural to surround and even 7.1.4ch monitor sets.
Switching and controlling the output destination B>
Up to 4 types of output destination routing can be saved from monaural to 7.1.4ch, and not only speaker switching, but also output level in routing can be controlled collectively, and solo / mute for each channel is also possible. ..
Remote control of the RED series mic input B>
You can switch the RED series mic input level, PAD, and input format.
Built-in talkback function B>
You can use the built-in microphone of REDNET R1 and the microphone connected to the microphone input terminal of the main unit as a talkback microphone. You can specify four output destinations for the talkback microphone, including I / O connected to the Dante network.
■ Features
・ Flexible monitor control
Top panel controls include level, reference level preset selection, cut, dim, mute, and various solo modes.
・ Speaker switching
With an A / B switch to switch between many monitoring presets and four foldable presets, you can quickly switch to check downmix.
・ Talkback function
The RedNet R1 has a built-in microphone for talkback. You can also connect any talkback mic to the XLR connector on the rear panel and send the talkback to any output on the I / O or RED series interface on the Dante network.
-Software / hardware control environment by RedNet Control
RedNet Control allows you to quickly configure complex monitoring and routing settings in software.
・ Foot switch input
1/4 inch jack socket can be used as a foot switch for talkback management and LFE mute
-Supports Power over Ethernet (PoE)
Powered via Ethernet (using PoE standard) or using DC power.
Internal talkback:
・ Gain range: 0dB to 55dB
・ Type: Balance, Zin = 3kΩ
・ Maximum input level: + 10dBu ± 0.5dB
External talkback
・ Gain range 0dB to 55dB
・ Gain range: Balance, Zin = 3kΩ
・ Maximum input level: + 10dBu ± 0.5dB
・ Frequency characteristics: 20Hz-20kHz ± 2dB
・ THD + N: -98dB (0.0012%) @ -1dBFS
・ EIN: -128dBu'A'-Weighted (typical)
・ SN ratio: -111dB'A'weight, minimum gain
・ CMRR (common mode rejection ratio): 50 / 60Hz CMRR: -77dB
Headphone output
・ All values are measured at the maximum output level (Rs = 600Ω).
・ 0dBFS reference level: + 11dBm
・ Frequency characteristics: 20Hz to 20kHz ± 0.5dB
・ THD + N: -100dB (0.001%) @ -1dBFS, Rs = 150R
・ Output impedance: 5Ω
-Headphone impedance: 32Ω-600Ω
Digital performance
-Supported sample rates: 44.1 / 48 / 88.2 / 96 kHz (-4% / -0.1% / + 0.1% / + 4.167%) at 24-bit
· Clock source: Internally or from the Dante network master
■ Rear panel connection, pot and switch
input
・ External talkback microphone input: 1 XLR (F)
・ Foot switch: 1 stereo jack
output
・ Headphone output: 1 stereo jack
Power switch: 1 switch
・ Talkback gain pot: 1 pot
-Talkback switch: Tri-state switch (external talkback + 48V, external talkback, internal talkback)
PSU & network connection
· PSU (PoE and DC): PoE input and DC 12V lock barrel input connector
-Network connector: Standard RJ45
Power supply
-Power over Ethernet (PoE): Compliant with IEEE 802.3af Class 0 Power-over-Ethernet standard (PoE A or PoE B compatible)
・ DC power supply: 12V 1.2A DC power supply
・ Power consumption: PoE: 10.3W, DC: 9W
商品レビューProduct Review
すべてのレビューを見る