IMAGENICS / CRO-H26R

A coaxial extender that, when combined with a transmitter such as CRO-H26T, can transmit HDMI (DVI) signals up to 210m using a single coaxial cable.

■Input signal:
Digital serial signal by original re-encoding method 1 system 1.0 Vp-p 75 Ω 2 distribution BNC x 2
Bit rate after original re-encoding
Video: 2.592 Gbps (fixed bit rate)
Audio: 9.216 Mbps (fixed bit rate)
Original bidirectional communication link function
■Output signal:
TMDS signal (digital RGB/YPbPr) HDMI-A connector 1 system (HDCP compatible, DVI signal output possible)
HDMI standard compliant signal (including embedded audio up to 8ch) or 24-bit full color DVI Rev1.0 standard compliant signal)
Pixel clock 25 MHz to 165 MHz, horizontal frequency 15 kHz to 200 kHz, vertical frequency 23 Hz to 240 Hz simultaneously satisfied, horizontal active pixels 320 to 2048, vertical active lines 240 to 1800 Automatically supports video signals up to
(Automatically supports HDMI signals equivalent to D1 to D5, and PC signals from VGA@60 to UXGA@60, WUXGA@60 (RB), and 2048x1152 (RB))
Output HDMI cable length is up to 5m when using our HDMI cable at maximum resolution
*This may be shorter depending on the HDMI output performance of the sending side.
■Analog audio output:
Analog output audio signal -10 dBu (10 kΩ or more load) Low impedance unbalanced 2-channel 1 system (φ3.5 stereo jack)
Audio frequency response: -1 dB to +1 dB at 20 Hz to 20 kHz
Audio S/N ratio: 85 dB or more (A-weighted at 1 kHz)
Audio crosstalk: 80 dB or more
Audio distortion rate: 0.03% or less
Maximum audio output level: +10 dBu (HDMI embedded audio input at 0 dBFS)
Audio sampling: 24 bit 48 kHz linear PCM method
■HDCP standard: Supports HDMI HDCP and DVI HDCP
■RS-232C:
RS-232C compliant full duplex D-Sub9 (male) 1 system
9,600 bps, 19,200 bps, 38,400 bps Switching between non-flow (default) and RTS/CTS hard flow
Switching between non-parity and even parity
■Coaxial transmission distance:
L-7CHD: 210m, L-5CFB: 110m, L-5C2V: 60m, L-3CFB: 60m, L-3C2V: 30m
(The distance may be shorter depending on the installation environment, etc.)
■Other functions:
HDMI→DVI signal conversion function
LED display function for input signal status, HDCP status, and link status
Built-in test pattern and tone generation function
Information function with on-screen display
And more. ■Special notes:
Not compatible with HDMI signal CEC, ARC, HEAC functions, deep color, or high bit rate audio standards
■Caution:
When using this unit in combination with an IMG.Link switcher (ILS-41, ILS-1616, etc.) or a distributor (CRO-ID18A, etc.), set the transmitter's EDID setting to built-in data (emulation function).
■Power supply: DC 5 V 0.6 A
■Power consumption: 3 W (maximum)
■Weight: Approximately 550 g
■SIZE: 100 (W) x 25 (H) x 150 (D) mm (excluding protrusions)
■Accessories:
1 AC 100 V 27 VA 50 Hz / 60 Hz domestic use only AC adapter (5 V 2.3 A output)
1 HDMI connector retaining bracket (CL-1)