FURMAN M-8X AR J Stabilized power supply 送料無料

FURMAN / M-8X AR J Stabilized power supply

Variations

This FURMAN 100V stabilized power supply features one AC outlet in the front and eight in the rear. Its safety circuit breaker trips when the total power draw exceeds 15 amps.

■100V Stabilized Power Supply
■1 AC Outlet in Front, 8 in Rear

Japanese voltage is typically 100VAC, but in reality, it fluctuates constantly due to fluctuations in power consumption and various other factors. Equipment cannot perform to its full potential with such an unstable power supply. This unit stabilizes the output voltage to 100VAC. Designed specifically for music use, it provides clean AC power in a variety of situations.

This unit uses an 8-tap toroidal autotransformer, which minimizes magnetic flux leakage and, thanks to its high efficiency, allows for a compact design.

This unit's voltage stabilization circuit accurately monitors the input voltage cycle by cycle. If the input voltage fluctuates and a different tap is selected, it compensates on a cycle-by-cycle basis without distorting the waveform of the incoming AC power.

Conventional voltage stabilizers that use multiple taps often change taps irregularly, causing voltage spikes and clicks that can even be mixed into the audio signal.

In addition, the hysteresis characteristics of this unit's switching circuit suppress unnecessary switching to adjacent taps, which can cause chatter. Unlike other stabilized power supplies that use ferroresonant transformers, this unit does not overreact to slight fluctuations in power supply frequency, creating an ideal power supply.

■ Voltage Stabilization
Regulates voltages from 81 VAC to 118 VAC to 100 VAC (±5V). This protects sensitive equipment from problems caused by unstable AC power, such as voltage drops and surges. Unstable power can cause changes in tone, data loss in digital equipment, and, in the worst case, equipment failure.
■ Noise Filter
This is a standard noise filter circuit. It reduces noise caused by RFI (radio frequency interference) and EMI (electromagnetic interference).
■ Surge Filter
Protects equipment from sudden high voltage surges. This is a standard surge protection circuit using a component called an MOV.
■ Abnormal Voltage Protection
If it detects abnormal fluctuations in the power supply voltage, it will shut down, protecting connected equipment from damage.
■ Current Protection
If it detects an overcurrent, it will cut off the power, protecting connected equipment.
■ 9 Outlets
There are eight outlets on the rear and one on the front. All outlets can be used interchangeably.
■ Circuit Breaker
This is a 15A circuit breaker that activates in the event of an overcurrent. The breaker trips if the total usage capacity exceeds the limit. Resetting is easy, with just the push of a switch. There is no need to carry a fuse.
■ Maximum supply current: 15 amps

■ There are nine power outlets in total, eight on the rear panel and one on the front panel.
■ Maximum input current is 15A, and output current is 12-15A.
■ Immediate shutdown occurs if excessive input voltage is detected, and shutdown occurs if input voltage is too low, except for momentary interruptions, to protect connected equipment.
■ Equipped with an EVS (Extreme Voltage Shutdown) LED.
■ Protects the unit and connected devices from overcurrent.
■ Equipped with an ECS (Extreme Current Shutdown) LED.
■ Operation status is displayed with a three-color LED.
■ Protection OK LED.
■ Input voltage can be checked with an 8-level LED.
■ Circuit breaker protects against overload.
■ Equipped with a toroidal transformer that minimizes magnetic flux leakage and noise.
■ Front panel on/off switch

■ Reference input voltage: 100 VAC 50/60Hz
■ Specified input voltage range: 81 VAC–118 VAC
■ Output voltage: 100 VAC ±5V
■ Output current rating: 15 amps at 103V input voltage
■ Output current derating: 136mA/volt, minimum 12.3A at 81V
■ EVS activation condition: 62 VAC or less or 125 VAC or more
■ ECS activation condition: 10 cycles at 100A, 1 cycle at 200A or more
■ Voltage meter accuracy: ±5 VAC
■ Spike protection mode: L-N
■ Spike clamping voltage: 400 V peak at 500A, L-N (UL-1449 3rd (Tested with ED)
■Spike Response Time: 1 nanosecond
■Maximum Surge Current: 15,000 amps
■Operating Humidity: < 90% rH (Relative Humidity)
■Maximum Spike Energy: 225 joules
■Noise Attenuation: -16dB @ 10kHz, -33dB @ 100kHz, -48dB @ 400kHz
■Dimensions: 44H x 483W x 279D mm
■Weight: 7.15 kg
■EMI: FCC Part 15 Class B